CARL GOLDBERG PRODUCTS LTD.P.O. Box 818, Oakwood, GA 30566 • 678-450-0085 • Fax: 770-532-2163 • www.carlgoldbergproducts.com©copyright 2003 Carl Gold
10Glue the joiner wire in place withepoxy. Make sure the elevators arelying on a flat surface so both willbe parallel. Use a straight edge tomake sure
11At the location of the elevator wiremake a notch approximately 3/16”deep and 3/8” wide to clear the ele-vator wire. At the location of thetiller arm
12Align the aileron control horn Usingthe line you drew earlier for thepushrod slot. Mark the location ofthe holes and drill two 5/64” holes.Install t
13The battery will mount on the leftside. Wrap with foam rubber(notshown for clarity) and insert intoopening.The receiver will mount on the rightside
14It will be necessary to cut the backside out of the nylon cover for thewires to fit in. Using a sharp knife,cut 1/16” inside the edge of thecover. M
15Align the elevator horn on the insideedge of the elevator and mount usingthe two #2x1” screws and nylonplate. Locate the two 2mm pushrods withclevis
16. If you use a mini servo these will notbe used. If you use a standard servoyou will need them to clear theservo. Assemble the tank cap with the big
17Mount the throttle servo using thehardware supplied with the radio.Use the1.5 mm x 6”pushrod and benda z bend in one end and attach to thethrottle a
18The CG should be between 4-3/4” and5-1/4” for first flight. For 3-D it canbe moved back after you are comfort-able with the plane.Have fun!AAddddiit
19Exit hole location tobe marked on thewing
2WWAARRNNIINNGG!! TTHHIISS IISS NNOOTT AA TTOOYY!!TTHHIISS IISS NNOOTT AA BBEEGGIINNNNEERRSS AAIIRRPPLLAANNEEThis R/C kit and the model you
20
21Optional Landing GearAvailableMake your Extreme 330 different from the crowed!Our new # 257 Profile Nylon Landing Gear will fit you Extreme 300 and
22EX-TREME 330 3-D ARF The Elevator This maneuver has your plane drop vertically in a nose high attitude, depending on wind conditions any where
23EX-TREME 330 3-D ARF The Waterfall This maneuver has your plane flipping around the axis of the wing, while dropping. Starting from a high
3Ex-trEx-treme 5eme 54040Congratulations on your purchase of the Lanier Ex-treme 540 3-D ARF. This isa very unique aircraft, with great 3-D capabilit
4Parts Layout
52.5mmx10mm screws 7 3 tail wheel mount 4 wire holder2.5mmx8mm screws 8 hatch covers2mmx20mm screws 8 control horns3mmx30mm screws 2 landing gear3mmx
6BUILDINGINSTRUCTIONSBefore starting to build this kit, weurge you to read through theseinstructions. They contain someimportant building sequences a
7It is easier to do some of the work onthe wing and fuselage before youglue them together. Locate the tem-plate at the rear of the book forlocating th
8measure back from the opening 1-3/8” and cut a slot 1/8” wide cen-tered on the mark you made.we are now ready to mount the wingon the fuselage.Slide
9Install the gear on the fuselageusing the two 3mmx30mm bolts, four3mm flat washer, and two 3mm locknuts.Locate the elevator joiner wire andthe two el
Kommentare zu diesen Handbüchern